What a Powder Coating Line Costs (and What Drives the Price)

What a powder coating line actually costs

Buyers usually ask for a price before they give a part size, and that is the wrong order. A coating line is priced from five blocks, and each block moves with a number you control. Understanding those blocks is the fastest way to compare quotations that look different but describe the same plant.

The five cost blocks

  1. Pretreatment — number of stages, tank or tunnel size, heating and the dry-off oven. A 5-stage dipping line can cost more than the booth and oven combined.
  2. Booth and recovery — booth width and height follow the largest part; recovery type (cyclone, mono-cyclone, cartridge) and colour-change design add cost.
  3. Curing oven — length follows line speed and dwell time; burner size follows part mass and conveyor load. Fuel choice changes the running cost far more than the purchase price.
  4. Conveyor — hanger load and whether parts must stop decides chain versus power-and-free. Power-and-free typically costs two to three times a plain overhead chain for the same length.
  5. Control, guns and ancillaries — gun count, reciprocators, workpiece detection, hoppers and the electrical panel.

Indicative ranges, and why they are ranges

As rough orientation for a single-shift plant: a compact manual line for parts up to about 1 m, with 3-stage pretreatment and one booth, is commonly quoted in the tens of thousands of US dollars; a mid-size automatic line with 4–5 stages, cyclone recovery and a zoned gas oven moves into the low-to-mid six figures; a large line with power-and-free conveying, several booths and full automation goes beyond that. Shipping, foundations, installation labour and local electrical work sit outside the equipment price and vary hugely by destination.

Anyone who quotes a firm number without asking for part size, output per shift and available floor space is quoting a catalogue item, not your line.

What to send for an accurate price

  • Largest workpiece: length × width × height, and weight per hanger
  • Coating type and target film thickness
  • Output target: parts or square metres per shift
  • Available floor length and width, ceiling height, and the fuel or power you have

Where projects overspend

Three patterns account for most budget overruns we see: a booth sized for the biggest part ever imagined rather than the parts actually quoted; a pretreatment line with more stages than the service environment requires; and a conveyor chosen for flexibility the product mix never uses. Each of those is a decision that can be made deliberately, with the part list in hand.

Frequently asked questions

Is a used line cheaper?

Sometimes on purchase, rarely on total cost. Used lines usually need new guns, new filters, a new burner and a conveyor rebuild, and the booth and oven rarely match your part size. If the parts fit the existing envelope, a used line can work well; if not, modification costs approach a new build.

Does a faster line reduce cost?

Only up to a point. Running faster shortens the booth and oven, but it also reduces dwell time and can force a longer oven to compensate. The economic point is usually set by the coating’s curing curve, not by the conveyor.

What is excluded from a typical quotation?

Normally shipping and insurance, foundations and pit work, installation labour and travel, local electrical supply and compressed air, powder or paint, and local permits. We state these explicitly in the offer so nothing appears later.

Related

Choosing a powder coating booth · Pretreatment stages · Powder coating lines

Send your part size for a budget price

BestCoatingLine

Powder coating lines, liquid painting lines and turnkey coating solutions. Engineered with specialist partner plants in Guangdong, China.

WhatsApp / WeChat: +86 156 0291 6761

[email protected]

Registered office

Sales departmentRoom D327, No. 42 Caiyun Road,
Longcheng Street, Longgang District,
Shenzhen, Guangdong, China

CompanyBEST MACHINES & EQUIPMENTS CO., LTD.

Production base

Project officeNo. 6-1, Dongsheng Road, Dongsheng Village,
Minzhong Town, Zhongshan,
Guangdong, China

Assembly base

Machining & assemblyChashan, Dongguan,
Guangdong, China

Working hoursMon-Sat, 08:30-18:00 (GMT+8)

© 2016-2026 BEST MACHINES & EQUIPMENTS CO., LTD. All rights reserved. Coating line solutions since 2016
Scroll to Top